WTB AGM Vent Nut/Nuts, Early.

Title should include: for sale, or for trade or wanted to buy. Pricing can be Buy it Now (BIN), Make Offer, or use both. Listing for 30 days or until cancelled by seller. One or more photos of each item. No Ebay Items. Caveat emptor & Caveat venditor.
Forum rules
Post Reply
User avatar
Rfieldbuilds
Super Colemanaholic
Posts: 1028
Joined: Sun Nov 05, 2017 5:12 pm

WTB AGM Vent Nut/Nuts, Early.

#1

Post by Rfieldbuilds »

I am looking for a vent nut or two that will fit an earlier AGM lantern. These are roughly 1/4”, and have a very fine thread pattern as was seen in models:
267, 268
277, 278
287,288.
If anyone knew this thread pitch, that would also be helpful. I have at least two lanterns in need so if you have a couple they would be put to good use. Thank You!
Regards,
Randy

Image
Last edited by Rfieldbuilds on Sat Jul 30, 2022 2:30 pm, edited 1 time in total.
Randy
QL #15, Slant Saver #59, #0269 Turd Hurdler, #0269 Mil Spec Syndicate, Coleman Blues 243 #0269, BernzOmatic Appreciation Club #072, Sears Traveler 2.0 Host #1, and a few others too.
Top
Majicwrench
Super Colemanaholic
Posts: 4238
Joined: Mon Jul 30, 2012 9:33 pm

Re: WTB AGM Vent Nut. Early.

#2

Post by Majicwrench »

Just took a thread gauge to one of mine, it's a 32 TPI
Keith
Top
User avatar
Rfieldbuilds
Super Colemanaholic
Posts: 1028
Joined: Sun Nov 05, 2017 5:12 pm

Re: WTB AGM Vent Nut/Nuts, Early.

#3

Post by Rfieldbuilds »

Majicwrench wrote: ↑Sat Jul 30, 2022 3:57 am Just took a thread gauge to one of mine, it's a 32 TPI
Thanks Bud. Now I know what to look for. Hopefully a couple show up here. I know someone has a drawer full.
Image
Randy
QL #15, Slant Saver #59, #0269 Turd Hurdler, #0269 Mil Spec Syndicate, Coleman Blues 243 #0269, BernzOmatic Appreciation Club #072, Sears Traveler 2.0 Host #1, and a few others too.
Top
Dmacp
Super Colemanaholic
Posts: 3307
Joined: Thu Dec 11, 2008 7:56 am

Re: WTB AGM Vent Nut/Nuts, Early.

#4

Post by Dmacp »

1/4-32. Same thread as a Coleman Check valve stem. They were closed on top. and had an asbestos faced aluminum washer under them. sorry I don't have any spares as I am still looking for them too.
Dan
ICCC member #604
Top
User avatar
Rfieldbuilds
Super Colemanaholic
Posts: 1028
Joined: Sun Nov 05, 2017 5:12 pm

Re: WTB AGM Vent Nut/Nuts, Early.

#5

Post by Rfieldbuilds »

Dmacp wrote: ↑Tue Aug 02, 2022 4:28 pm 1/4-32. Same thread as a Coleman Check valve stem. They were closed on top. and had an asbestos faced aluminum washer under them. sorry I don't have any spares as I am still looking for them too.
Update: Still Looking.


Dan. I think we may be down to just having some made. Im speaking with a machinist now and sent some pics and dimensions. Check back here in a while and we will see if this gets off the ground. Would you be interested in any if these get fabricated? They wont be cheap, but should look pretty close to original.
Randy
QL #15, Slant Saver #59, #0269 Turd Hurdler, #0269 Mil Spec Syndicate, Coleman Blues 243 #0269, BernzOmatic Appreciation Club #072, Sears Traveler 2.0 Host #1, and a few others too.
Top
Dmacp
Super Colemanaholic
Posts: 3307
Joined: Thu Dec 11, 2008 7:56 am

Re: WTB AGM Vent Nut/Nuts, Early.

#6

Post by Dmacp »

yes Randy, I'd be interested.
Dan
ICCC member #604
Top
Jeremy_71
Member
Posts: 28
Joined: Sat May 30, 2020 7:12 pm

Re: WTB AGM Vent Nut/Nuts, Early.

#7

Post by Jeremy_71 »

I would also be interested in a few. Keep me updated please
Jeremy Mitchell

"If you don't learn something everyday...You have wasted the day" 
my Grandfather

Mil Spec Syndicate #2115
Coleman Blues 243’s #2115
Top
User avatar
Rfieldbuilds
Super Colemanaholic
Posts: 1028
Joined: Sun Nov 05, 2017 5:12 pm

Re: WTB AGM Vent Nut/Nuts, Early.

#8

Post by Rfieldbuilds »

Jeremy_71 wrote: ↑Wed Aug 03, 2022 4:23 pm I would also be interested in a few. Keep me updated please
Dan, Jeremy- You got it. I will let ya know what I hear. In FB Jail at the moment so a little slow communicating on that side thanks to my pal Zuckerturd. FWIW, I have some smaples coming from the Eastern US, but not sure if that machinist is willing to produce in any quantity. Another machinist is working on it, and will ikely be able to fill a small size order for a few guys. What would be awesome is if someone here knew a guy with a screw machine. That would be the best option for a reasonable price on enough quantity to keep everyone happy.
Randy
QL #15, Slant Saver #59, #0269 Turd Hurdler, #0269 Mil Spec Syndicate, Coleman Blues 243 #0269, BernzOmatic Appreciation Club #072, Sears Traveler 2.0 Host #1, and a few others too.
Top
Post Reply

Return to “Classifieds”